Configuring the Switch This appendix contains these topics: • • • Accessing the CLI Through Express Setup You can access the CLI on an unconfigured switch. Set the switch in Express Setup mode and connect a switch Ethernet port to an Ethernet port on your PC or workstation. Follow the steps described in the getting started guide for turning on the switch and using Express Setup.

• Cisco Usb Console Driver 2960
• Windows 10 Cisco Usb Console Driver

Hello All, I want a USB Driver for the USB Console cable which came up with Cisco Router. Note that this USB Console cable has both the sides USB ports ( 1 si 75907. Obtain the Cisco USB console driver file from the Cisco.com web site and unzip it. If using 64-bit Windows Vista or Windows 7, double-click the setup.

When the switch is in Express Setup mode, open a Telnet session to the switch by entering the IP address 10.0.0.1. Enter the setup user EXEC command. Enter the information described in and. After you have entered the configuration information for the switch, save it to flash memory by using the write memory privileged EXEC command. Note In Express Setup mode, the IP address 10.0.0.1 remains active on the switch until you enter the write memory command.

You lose the Telnet connection after entering the write memory command. Accessing the CLI Through the Console Port You can access the CLI on a configured or unconfigured switch by connecting the RJ-45 console port or USB console port of the switch to your PC or workstation and accessing the switch through a terminal emulation program. Note If you have stacked your switches, connect to the console port of one of the switches in the stack. You can initially configure the entire stack from any member switch. • • • • Connecting the RJ-45 Console Port Procedure Step 1 Connect the RJ-45-to-DB-9 adapter cable to the 9-pin serial port on the PC.

Cisco Usb Console Driver 2960

Connect the other end of the cable to the switch console port. Step 2 Start the terminal-emulation program on the PC or the terminal. The program, frequently a PC application such as HyperTerminal or ProcommPlus, makes communication between the switch and your PC or terminal possible. Step 3 Configure the baud rate and character format of the PC or terminal to match the console port default characteristics: • 9600 baud • 8 data bits • 1 stop bit • No parity • None (flow control) Step 4 Power on the switch as described in the switch getting started guide. Step 5 The PC or terminal displays the bootloader sequence. Press Enter to display the setup prompt.

Have you tried promise fasttrak tx4650 driver install this proggie on a 32-bit machine? If so, click 'Accept as Solution' in the bottom right hand corner cisco usb console driver windows 7 64 the post. Logos remain the property of the driiver company. The Cisco USB Console creates 2 devices under Device Manager: The Cisco USB Com Port, and a device called the 'Cisco. I just purchased a USB to Mini-USB console cable to use with the 2960s switches we just bought. I download the current(?) driver Ver. 3.1 loaded it on my Win 7 64-bit laptop.

Connecting the USB Console Port Procedure Step 1 If you are connecting the switch USB console port to a Windows-based PC for the first time, install the USB driver. Note USB Type A port on the switch provides file system support and is NOT a console port.

See USB Type A Port section. Connecting the USB Console Cable to the Switch 1 USB console port (5-pin mini-Type B) 3 USB Type A connection on the laptop 2 USB Type A to 5-pin mini-Type B cable Step 2 Connect a USB cable to the PC USB port. Connect the other end of the cable to the switch mini-B (5-pin-connector) USB console port. Step 3 Start the terminal-emulation program on the PC or the terminal.

The program, frequently a PC application such as HyperTerminal or ProcommPlus, makes communication between the switch and your PC or terminal possible. Step 4 Configure the baud rate and character format of the PC or terminal to match the console port default characteristics: • 9600 baud • 8 data bits • 1 stop bit • No parity • None (flow control) Step 5 Power on the switch as described in the switch getting started guide. Step 6 The PC or terminal displays the bootloader sequence.

Press Enter to display the setup prompt. Follow the steps in the Setup program. Installing the Cisco Microsoft Windows USB Device Driver A USB device driver must be installed the first time a Microsoft Windows-based PC is connected to the USB console port on the switch. • • • • • • Installing the Cisco Microsoft Windows XP USB Driver Procedure Step 1 Obtain the Cisco USB console driver file from the Cisco.com web site and unzip it. Note You can download the driver file from the Cisco.com site for downloading the switch software. Step 2 If using 32-bit Windows XP, double-click the setup.exe file in the Windows_32 folder. If using 64-bit Windows XP, double-click the setup(x64).exe file in the Windows_64 folder.

Step 3 The Cisco Virtual Com InstallShield Wizard begins. Step 4 The Ready to Install the Program window appears. Click Install. Step 5 The InstallShield Wizard Completed window appears. Click Finish. Step 6 Connect the USB cable to the PC and the switch console port.

The USB console port LED turns green, and the Found New Hardware Wizard appears. Follow the instructions to complete the driver installation. Installing the Cisco Microsoft Windows 2000 USB Driver Procedure Step 1 Obtain the Cisco USB console driver file from the Cisco.com web site and unzip it.

Note You can download the driver file from the Cisco.com site for downloading the switch software. Step 2 Double-click the setup.exe file. Step 3 The Cisco Virtual Com InstallShield Wizard begins. Step 4 The Ready to Install the Program window appears. Click Install. Step 5 The InstallShield Wizard Completed window appears. Click Finish.

Step 6 Connect the USB cable to the PC and the switch console port. The USB console port LED turns green, and the Found New Hardware Wizard appears. Follow the instructions to complete the driver installation. Installing the Cisco Microsoft Windows Vista and Windows 7 USB Driver Procedure Step 1 Obtain the Cisco USB console driver file from the Cisco.com web site and unzip it.

Selama ini dia tidak pernah mendapat nilai bagus dan selalu dimarahi bibinya. Sayangnya, pada saat Karin akan lulus, Shi mati. Ia akan bersemangat kalau bersama kucingnya, Shi. Kamichama karin chu manga. Namun Karin tetap semangat.

Note You can download the driver file from the Cisco.com site for downloading the switch software. Step 2 If using 32-bit Windows Vista or Windows 7, double-click the setup.exe file in the Windows_32 folder. If using 64-bit Windows Vista or Windows 7, double-click the setup(x64).exe file in the Windows_64 folder. Step 3 The Cisco Virtual Com InstallShield Wizard begins. Step 4 The Ready to Install the Program window appears. Click Install.

Note If a User Account Control warning appears, click Allow - I trust this program to proceed. Step 5 The InstallShield Wizard Completed window appears. Click Finish. Step 6 Connect the USB cable to the PC and the switch console port. The USB console port LED turns green, and the Found New Hardware Wizard appears. Follow the instructions to complete the driver installation. Uninstalling the Cisco Microsoft Windows USB Driver Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver Use the Windows Add or Remove Programs utility or the setup.exe file.

Using the Setup.exe Program Before You Begin Disconnect the switch console terminal before uninstalling the driver. Procedure Step 1 Run setup.exe for Windows 32-bit or setup(x64).exe for Windows-64bit. Step 2 The InstallShield Wizard for Cisco Virtual Com appears.

Step 3 When the Program Maintenance window appears, select the Remove radio button. Step 4 When the Remove the Program window appears, click Remove. Step 5 When the InstallShield Wizard Completed window appears, click Finish.

Using the Add or Remove Programs Utility Before You Begin Disconnect the switch console terminal before uninstalling the driver. Procedure Step 1 Click Start > Control Panel > Add or Remove Programs. Step 2 Scroll to Cisco Virtual Com and click Remove.

Windows 10 Cisco Usb Console Driver

Step 3 When the Program Maintenance window appears, select the Remove radio button. Uninstalling the Cisco Microsoft Windows Vista and Windows 7 USB Driver Before You Begin Disconnect the switch console terminal before uninstalling the driver.

Procedure Step 1 Run setup.exe for Windows 32-bit or setup(x64).exe for Windows-64bit. Step 2 The InstallShield Wizard for Cisco Virtual Com appears. Step 3 When the Program Maintenance window appears, select the Remove radio button. Step 4 When the Remove the Program window appears, click Remove. Note If a User Account Control warning appears, click Allow - I trust this program to proceed.

Step 5 When the InstallShield Wizard Completed window appears, click Finish. Entering the Initial Configuration Information To set up the switch, you need to complete the setup program, which runs automatically after the switch is powered on. You must assign an IP address and other configuration information necessary for the switch to communicate with the local routers and the Internet. This information is also needed to use Device Manager or Cisco Network Assistant to configure and manage the switch. • • IP Settings Obtain this information from your network administrator before you start the setup program: • Switch IP address • Subnet mask (IP netmask) • Default gateway (router) • Enable secret password • Enable password • Telnet password Completing the Setup Program If your switches are stacked and there are multiple console connections to individual switches in the stack, the initial setup dialog box appears at the console where you first press Enter. Procedure Step 1 Enter Yes at these two prompts: Would you like to enter the initial configuration dialog? [yes/no]: yes At any point you may enter a question mark '?'

Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system. Would you like to enter basic management setup?

[yes/no]: yes Step 2 Enter a host name for the switch, and press Return. On a command switch, the host name is limited to 28 characters; on a member switch the name is limited to 31 characters. Do not use -n, where n is a number, as the last character in a host name for any switch. Enter host name [Switch]: host_name Step 3 Enter an enable secret password, and press Return.

The password can be from 1 to 25 alphanumeric characters, can start with a number, is case sensitive, allows spaces, but ignores leading spaces. The secret password is encrypted, and the enable password is in plain text. Enter enable secret: secret_password Step 4 Enter an enable password, and press Return. Enter enable password: enable_password Step 5 Enter a virtual terminal (Telnet) password, and press Return.

The password can be from 1 to 25 alphanumeric characters, is case sensitive, allows spaces, but ignores leading spaces. Enter virtual terminal password: terminal-password Step 6 To configure the country code, enter yes and press Return. Do you want to configure country code? [no]: yes Step 7 Enter the country code, and press Return. Enter the country code[US]: US Step 8 (Optional) Configure Simple Network Management Protocol (SNMP) by responding to the prompts. You can also configure SNMP later through the CLI, Device Manager, or the Network Assistant application. To configure SNMP later, enter no.

Configure SNMP Network Management? [no]: no Step 9 Enter the interface name (physical interface or VLAN name) of the connection to the management network, and press Return.

For this release, always use vlan1 as that interface. Enter interface name used to connect to the management network from the above interface summary: vlan1 Step 10 Configure the interface by entering the switch IP address and subnet mask and pressing Return. The IP address and subnet masks shown are examples. Configuring interface vlan1: Configure IP on this interface? [yes]: yes IP address for this interface: 10.4.120.106 Subnet mask for this interface [255.0.0.0]: 255.0.0.0 Step 11 Enter Y to configure the switch as the cluster command switch. Enter N to configure it as a member switch or as a standalone switch.

If you enter N, the switch appears as a candidate switch in the Network Assistant GUI. You can configure the switch as a command switch later through the CLI, Device Manager, or the Network Assistant application. To configure it later, enter no. Would you like to enable as a cluster command switch? [yes/no]: no You have now completed the initial configuration of the switch. This is an example of the configuration output that appears: The following configuration command script was created: hostname switch1 enable secret 5 $1$Ulq8$DlA/OiaEbl90WcBPd9cOn1 enable password enable_password line vty 0 15 password terminal-password no snmp-server!

No ip routing! Interface Vlan1 no shutdown ip address 10.4.120.106 255.0.0.0! Interface GigabitEthernet1/0/1! Interface GigabitEthernet1/0/2 interface GigabitEthernet1/0/3!! Interface GigabitEthernet1/0/23! End Step 12 From these choices that appear, make your selection and press Return.

[0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config.

[2] Save this configuration to nvram and exit. Choose (2) to save the configuration to NVRAM to use it the next time the switch reboots. Enter your selection [2]: 2 The switch now runs this default configuration. If you want to change this configuration or perform other management tasks, see.

Attention, Internet Explorer User Announcement: Jive has discontinued support for Internet Explorer 7 and below. In order to provide the best platform for continued innovation, Jive no longer supports Internet Explorer 7. Jive will not function with this version of Internet Explorer. Please consider upgrading to Internet Explorer 8, 9, or 10, or trying another browser such as Firefox, Safari, or Google Chrome.

(Please remember to honor your company's IT policies before installing new software!) • • • •.